5 Ton 15.2 SEER2 Goodman Heat Pump Split System GSZH506010+AMST60DU1400
Standard Features
• High-efficiency scroll compressor
• SmartShift® technology to ensure quiet reliable defrost
• Copper tube/ enhanced aluminum fin coil- 5mm diameter on 1.5-3.5T
• Factory-installed suction-line accumulator
• Factory-installed compressor crankcase heater
• Factory-installed high-capacity muffler
• High- and low-pressure switches
• Service valves with sweat connections and easy access to gauge ports
• Fully charged for 15’ of tubing length
• Contactor with lug connection
• Ground lug connection
• AHRI Certified; ETL Listed
Cabinet Features
• Removable grille style top design compliant with UL 60335-2-40
• Steel louver coil guard
• Heavy-gauge galvanized-steel cabinet
• Attractive Architectural Gray powder-paint finish with 500-hour salt-spray approval
• Top and side maintenance access
• Single panel access to controls with space provided for field-installed accessories
• When properly anchored, meets the 2020 Florida Building Code unit integrity requirements for
hurricane-type winds
(Anchor bracket kits available.)
¹ Tested and rated in accordance with AHRI Standard 210/240
² Wire size should be determined in accordance with National Electrical Codes; extensive wire runs
will require larger wire sizes ³ Must use time-delay fuses or HACR-type circuit breakers of the same size as noted.
Notes
• Always check the S&R plate for electrical data on the unit being installed.
• Installer will need to supply ⅞” to 1⅛” adapters for suction line connections.
• Unit is charged with refrigerant for 15’ of ⅜” liquid line. System charge must be adjusted per Installation Instructions Final Charge Procedure.
• Installation of these units requires the specified TXV Kit to be installed on the indoor coil.
THE SPECIFIED TXV IS DETERMINED BY THE OUTDOOR UNIT NOT THE INDOOR COIL.
GSZH506010
| Model | GSZH506010 |
| Nominal Capacities | |
| Cooling (BTU/h) | 60,000 |
| Heating (BTU/h) | 60,000 |
| SEER2 | 15.2 |
| Decibels | 76 |
| Compressor | |
| RLA | 25.6 |
| LRA | 151 |
| Stage | Two |
| Type | Scroll |
| Condenser Fan Motor | |
| Horsepower | 1/5 |
| FLA | 1.0 |
| Refrigeration System | |
| Refrigerant Line Size¹ | |
| Liquid Line Size (“O.D.) | ⅜" |
| Suction Line Size (“O.D.) | 1⅛" |
| Refrigerant Connection Size | |
| Liquid Valve Size (“O.D.) | ⅜" |
| Suction Valve Size (“O.D.) | ⅞" |
| Valve Connection Type | Sweat |
| Refrigerant Charge (oz.) | 276 |
| Electrical Data | |
| Volts/Phase (60 Hz) | 208/230 |
| Minimum Circuit Ampacity ² | |
| Max. Overcurrent Protection ³ | 50 |
| Min / Max Volts | 197/253 |
| Electrical Conduit Size | 1/2" or 3/4" |
| Unit Weights | |
| Equipment Weight | 309 |
| Shipping Weight | 329 |
Product Features
• Internal factory-installed thermal expansion valves for cooling and heat pump applications
• Direct drive, multi-speed ECM blower motor
• All-aluminum evaporator coil
• Coil mounting track for quick repositioning
• Optimized for use with R-410A refrigerant
• Cabinet air leakage less than 2.0% at 1.0 inch H₂O when tested in accordance with ASHRAE standard193
• Cabinet air leakage less than 1.4% at 0.5 inch H₂O when tested in accordance with ASHRAE standard193
• AHRI certified; ETL listed
• Rigid SmartFrame™ cabinet
• Horizontal or vertical configuration capabilities
• 21” depth for easier attic access
• DecaBDE-free thermoplastic drain pan with secondary drain connections
• Screw-less sides and back helps to reduce con- densation when installed in humid locations
• Foil-faced insulation covers the internal casing to reduce cabinet condensation
• Galvanized, leather grain-embossed finish
• Glue-less cabinet insulation retention
• Tool-less filter access
• Field Installed 3 kW – 25 kW electric heater kits available
AMST60DU1400
| Model | AMST60DU14* |
| Nominal Ratings | 60,000 |
| Cooling (Btu/h) | |
| Blower | |
| Diameter | 11" |
| Width | 10" |
| Coil Connections | |
| Liquid | 3/8" |
| Suction | 7/8" |
| Coil Drain Connect (FPT) | 3/4” |
| Electrical Data | |
| Voltage | 208/230 |
| Minimum Circuit Ampacity | 8.6/8.6 |
| Max. Overcurrent Device (Amps) | 15/15 |
| Minimum VAC | 197 |
| Maximum VAC | 253 |
| Blower Motor | |
| Full Load Amps (FLA) | 6.9 |
| Horsepower (HP) | ¾ |
| Ship Weight (Lbs.) | 167 |
AMST60DU1400 Heat Kit Specs
| Heater Kit Model | Circuit 1 | Circuit 2 | Single-Point Kit | |||||
| Heater Amps | Mininum Circuit Ampacity 208/230 | Max Over Current Protection 208/230 | Heater Amps | Mininum Circuit Ampacity 208/230 | Max Over Current Protection 208/230 | Mininum Circuit Ampacity 208/230 | Max Over Current Protection 208/230 | |
| AMST60DU1400 | 0/0 | 8.6/8.6 | 15/15 | |||||
| 3 KW | 10.8/12.5 | 22/24.3 | 25/25 | |||||
| 5 KW | 17.3/20 | 30.3/34 | 35/35 | |||||
| 6 KW | 21.7/25 | 36/39.9 | 40/40 | |||||
| 8 KW | 28.9/33.3 | 45/50.3 | 45/60 | |||||
| 10 KW | 34.7/40 | 52/58.6 | 60/60 | |||||
| 15 KW | 40 | 58.6 | 60 | 20 | 25 | 25 | 83.6 | 90 |
Product Documents
$5,843.00
Out of stock
