(This Product Is Discontinued)
Install Kit Includes:
* 50′ Copper Insulated Line Set
* Drain Float Switch
* 6′ Electrical Whip
* 60 amp non fused disconnect
* Plastic Condenser Pad
* Digital Thermostat
* Heat Strip up to 10 kw
Standard Features
- High-efficiency scroll compressor
- SmartShift® technology to ensure quiet reliable defrost
- Single-speed ECM condenser fan motor
- Factory-installed bi-flow liquid-line filter drier
- Factory-installed suction-line accumulator
- Factory-installed compressor crankcase heater
- Factory-installed high-capacity muffler
- High- and low-pressure switches
- Service valves with sweat connections and easy access to gauge ports
- Copper tube/enhanced aluminum fin coil
- Fully charged for 15’ of tubing length
- Contactor with lug connection
- Ground lug connection
- AHRI Certified; ETL Listed
Cabinet Features
- Goodman® brand sound control top design
- Steel louver coil guard
- Heavy-gauge galvanized-steel cabinet
- Attractive Architectural Gray powder-paint finish with 500-hour salt-spray approval
- Top and side maintenance access
- Service ports and controls are accessible while unit is operating
- When properly anchored, meets the 2010 Florida Building Code unit integrity requirements for hurricane-type winds
| GSZ160301 | |
| Nominal Capacities | |
| Cooling (BTU/h) | 30,000 |
| Heating (BTU/h) | 30,000 |
| Decibels | 75 |
| Compressor | |
| RLA | 13.4 |
| LRA | 72.5 |
| Type | Scroll |
| Condenser Fan Motor | |
| Horsepower | 1/6 |
| FLA | 1.1 |
| Refrigeration System
Refrigerant Line Size¹ | |
| Liquid Line Size (“O.D.) | 3/8″ |
| Suction Line Size (“O.D.) | 3/4″ |
| Refrigerant Connection Size | |
| Liquid Valve Size (“O.D.) | 3/8″ |
| Suction Valve Size (“O.D.) | 7/8” |
| Valve Connection Type | Sweat |
| Refrigerant Charge (oz.) | 160 |
| Electrical Data | |
| Volts/Phase (60 Hz) | 208/230 |
| Minimum Circuit Ampacity ² | 18.0 |
| Max. Overcurrent Protection ³ | 30 |
| Min / Max Volts | 197/253 |
| Electrical Conduit Size | 1/2″ or 3/4″ |
| Unit Weights | |
| Equipment Weight | 186 |
| Shipping Weight | 206 |
Product Features
-Internal factory-installed thermal expansion – Rigid SmartFrame™ cabinet
Product Features
valves for cooling and heat pump applications – Horizontal or vertical configuration capabilities
-Direct drive, multi-speed ECM blower motor -21” depth for easier attic access
-Coil mounting track for quick repositioning – DecaBDE-free thermoplastic drain
-Optimized for use with R-410A refrigerant pan with secondary drain connection
-Cabinet air leakage less than 2.0% – Screw-less sides and back helps
at 1.0 inch H₂O when tested in to reduce condensation when
accordance with ASHRAE standard 193 installed in humid locations
-Cabinet air leakage less than 1.4% – Foil-faced insulation covers the internal
at 0.5 inch H₂O when tested in casing to reduce cabinet condensation
accordance with ASHRAE standard 193 -Galvanized, leather grain-embossed finish
-AHRI certified; ETL listed -Glue-less cabinet insulation retention
-Tool-less filter access
-Field Installed 3 kW – 25 kW electric heater
kits available
| ASPT37C14 | |
| Nominal Ratings | |
| Cooling (Btu/h) | 36,000 |
| Blower | |
| Diameter | 10⅝” |
| Width | 8″ |
| Coil Connections | |
| Liquid | ⅜” |
| Suction | ⅞” |
| Coil Drain Connect (FPT) | ¾” |
| Electrical Data | |
| Voltage | 208/230 |
| Minimum Circuit Ampacity | 5.6 / 5.6 |
| Max. Overcurrent Device (Amps) | 15 / 15 |
| Minimum VAC | 197 |
| Maximum VAC | 253 |
| Blower Motor | |
| Full Load Amps (FLA) | 4.5 |
| Horsepower (HP) | ¾ |
| Ship Weight (Lbs.) | 144 |
$4,071.00
-
